Hanging the door was definitely the most tedious part of this project! It took a lot of patience to get the door level. To make matters more complicated, one of the door hinges came with stripped screws which caused the door to sag and pull away from the frame. Fortunately we were able to get a repair recommendation from the manufacturer Mastercraft. We drilled out the holes to fit small wooden dowels, glued them in, and cut them flush with the door. After allowing them to dry, we were able to re-drill holes for the hinge.
Aside from a few unexpected twists and turns, we have pretty much finished the door install! All it needs now is some insulating, trim work, and paint. Check the screen panel for square. If it is out of square, stand it on one corner and pull down on the opposite corner. Install the sliding screen and adjust it so it slides easily.
Apply a bead of exterior caulk all around the exterior trim. Set any nails below the surface. Fill nail or screw holes with a dot of caulk. Follow manufacturer's instructions for sealing the opening. In this arrangement, pieces of building paper and self-stick flashing tape are cut to fit and installed in the correct order, so water has no chance of seeping behind and damaging the house's sheathing.
How to Install a Patio Door. You spent time and money building your patio, so now learn how to access it with ease. Installing a patio door is not much more difficult than installing a standard entry door.
May 30, Save Pin FB More. Editor's Tip. Editor's Tip A set of hinged patio doors installs much like a slider but also has some of the challenges of hanging a standard exterior door. Editor's Tip Follow manufacturer's instructions for sealing the opening.
View Series. Comments Add Comment. How difficult was this project? Very easy. Kind of easy. Kind of hard. Very hard. Font Size Print Pin Save. Back to project Comment on this project. Tell us what worked, what didn't, and if you made adjustments Thanks for adding your feedback.
This can help to prevent flying debris from damaging the wood. Once the patio door is affixed to the masonry, the open gaps between the two need to be filled with appropriate insulating material. If you want to use foil for the interior sealing and sealing tape for the outside, the tape will have to fully expand before you can begin the foaming procedure.
The installation of the door frame is almost complete now and the three different seals have either been applied or attached. The final step of the procedure is to insert and adjust the leaf Fig. You do not necessarily need professionals to install your patio door. The information in this manual can help anyone with the installation of patio doors and windows step by step.
This manual not only teaches you about the installation of new patio doors, it also allows you to save money by doing the work yourself. Installing windows and balcony doors should also not be a problem for you, as the two procedures are very similar.
Shop Info About windows Materials The new patio door Screws for the frame Washers Vapour-resistant foil Foil open to vapour diffusion Trioplex tape if available Construction foam Construction foam cleaner Blueprints Pen or pencil. Preparations To ensure the smooth installation of a patio door, all necessary tools and materials should be placed within reach beforehand, so they can be used without delay during the procedure.
Clean the patio door reveal, making sure that no dust or dirt particles remain. Ideal thermal insulation values can only be achieved if the new patio door is installed onto clean surfaces. Clean surface conditions allow the sealing material to fully stick to the reveal, allowing for a fault-free installation procedure Fig. Re-measure the reveal before installation. This way, you can be sure that the measurements of the new patio door actually match those of the reveal.
If building blueprints are available, you should also note the measurements and the date in writing. Always focus on personal safety during installation.
In order to minimise the risk of injury during the installation of a heavy and unwieldy patio door, an additional helper could be of great benefit. Furthermore, you should always wear solid shoes, safety gloves and protective goggles while drilling. Preparing the Patio Door In order to avoid shipping damage, special protective foils are applied to the exterior surfaces of patio doors and windows.
Attach the handle in the correct position on the door and open the leaf. Next, the crew sealed around the door frame the space where the shims were inserted. They also ripped the brick moulding to fit back in place. The new door looks a lot better so you have improved curb appeal. What was the original reason for replacing the doors though?
I know you discovered that the header was too weak, but that might not have been discovered if not for replacing the doors in the first place. The homeowner wanted to replace the doors as phase 1 of remodeling their basement. Another great article.
One thing to add is that wetting the finger I use soapy water if available makes for a much smoother joint. I like that they used PVC on the vertical instead of treated 1x material. More expensive but it will never rot. Looks good. I like the pvc rather than wood, which would eventually rot in a basement situation like this.
I think PVC trim is the way to go. Dont they make composite shims that are rot proof? The install looks great though! The do make composite shims. Much improved over the old door.
0コメント